Christmas, Craft Projects, DIY GIFT GUIDE, Gift Idea, Holiday, Quick and Easy Crafts, Wine Crafts

DIY GIFT GUIDE: Cork LOVE Magnets

Cork LOVE Magnets

Day two of the gift guide and what do we have — stamped cork magnets!

If you don’t think these are adorable, well you might be cray cray.

You’ll love how easy peasy this project is. It takes 5 minutes, tops!

Supplies: 

  • Corks
  • Small stamps
  • Magnets (Michaels sells round magnets that are slightly smaller that a cork round. Match made in heaven? I think so!)
  • Ink
  • Hot glue
  • Cutting tool

Steps:

  1. Like in yesterday’s post, carefully slice your corks to about a 1/2-inch thickness. You can use a steak knife, scissors (if the are really sharp) or any other tool you have that might cut through the cork.
  2. Stamp each cork round with your small stamp and ink. It might take you a few tries to get your stamp centered the way you like it. Some of the LOVE stamps looked more like LOVF. Oops.
  3. Place a dab of hot glue on the back of the cork and secure it to the magnet. Let cool.
  4. Stick your magnets on your fridge and marvel at their cuteness.

Love Magnets

Is there a wine lover in your family who would love these!? There are definitely a few people in my family who I think would like them!

Love magnets2

Check back tomorrow for the next DIY gift post!

 

Advertisements
Craft Projects

Beautified Bar Tray

Have you ever used EnviroTex Lite? I have, and it is awesome. A “pour on high gloss finish,” it makes objects it is poured on look like they covered in glass. Can you see where I’m going with this post? Good 🙂

I picked up an old silver tray at a thrift store (yes, me and my thrift stores… we are in love). Unlike most other trays I’ve seen at thrift stores, this one was long, skinny, rectangular and had wooden handles. I had to have it, especially for a mere $3.92, or something close to that. I thought I’d decoupage the tray, then I had a better idea — the tray would fit perfectly on our bar, so why not line it with bottle caps and pour the EnviroTex Lite on for a fun finish? Perfecto.

Before you ask any questions about the next part of my post, let me say that I don’t drink much beer at all (less than 10 a year, if I had to guess) and I am very sober writing this post. Glad we got that cleared up.

Next, I dug through my stash of bottle caps and picked out the ones I wanted to use in my tray. I have a lot of bottle caps. A lot. In fact, I have an entire fish bowl full of them. It’s impressive really, considering I hardly ever drink beer. But thanks to my kleptomania (yes, I steal bottle caps when I see people drinking a beer with a cool cap) and my friends and family who enjoy beer (that makes them sound like drunkards. They aren’t. No worries!), I had plenty to choose from. Even more impressive is that I was able to pick out 46 unique bottle caps from my collection. Holy cow, this tray was meant to be! Not to mention, the caps fit perfectly in the inset of the tray, leaving about 2 mm on top for the EnviroTex to dry and harden. Score!

Once I had my caps selected, I picked an order for the tray. I swapped things around a few times before I cam up with an arrangement I liked. I went with a color gradient, starting at white and ending with black.

With an arrangement I liked, I removed the caps and set them out in front of the tray, keeping everything in order.

Next, I had to remove the wood handles — those needed some black paint. I unscrewed them from the bottom of the tray.

After the handles were off, I cleaned the tray really well using silver polish. It was pretty grimy. Yuck-o.

Then it was time to secure my caps, which I am so glad I did (to most of them). I’ll skip ahead here for one sec — as I was pouring the EnviroTex onto my caps, the caps I didn’t secure well floated to the top. Whoops! I had to push them down to get out the air bubbles underneath so the EnviroTex could harden.

So secure my bottle caps I did two things: Hot glue and magnets. Some of the bottle caps I chose to use I’d already made into refrigerator magnets. I decided they’d look better in my tray than on my fridge, so I plopped them in and they clung tight to the metal tray. That was awesome because those suckers didn’t move later.

For the other caps with no magnets, I filled them with hot glue then stuck them onto the tray. If you are going to try this, definitely make sure they are stuck on really well or you’ll have some float-away caps, too.

Once all of my caps were secure, I mixed my EnviroTex together, following the directions on the box closely. When ready, I poured it over my caps.

Here’s the cruddy part about my project… each box of EnviroTex was 4 oz., which covers 1 square foot. I have no concept of 1 square foot, so I ordered two boxes thinking I’d only need one. I needed four.

To let the tray dry (for 72 hours… twice haha), I covered it so no dust would settle on top of the tray. My cupcake holder lid did the trick rather nicely.

Needless to say, this project took a little bit longer than I anticipated. It was also a lot more expensive than I ever dreamed it would be (I hate when that happens). But it turned out beautifully, and four layers of EnviroTex Lite and two freshly painted black handles later I had a beautiful tray.

 

 

It looks really nice on our bar, fitting perfectly on the top ledge. It’s a real statement piece and I am so pleased with how it turned out. The hubby loves it, too.

Next time around, I think I’ll use something that isn’t as deep as a bottle cap, that way I won’t need nearly as much EnviroTex as I did for this tray. I might preserve a coin collection!! How cool would that be?

Thanks for stopping by!

 

Quick and Easy Crafts

Project 4: Vintage Flower Magnets

Here’s another quick and easy project to do with magnets.

I’ve been holding onto a set of vintage flower pins trying to decide what I’d like to do with them. The pins are very beautiful and colorful, but they were too heavy to pin to a thin sweater and I don’t own the type of coat that they would look cute pinned to.

So, I decided that I would turn them into magnets and give them to some of my coworkers to dress up their offices (I work with a lot of women — don’t worry, I didn’t force flower magnets on the men.)

So, here are the three easy steps to creating magnets from old pins:

1. Remove the pin backing from the decorative flower:

This is the only tough part of the project. Some of the pins were more stubborn than others. I used pliers to bend the metal back and forth until it broke. On a second pin, I tried cutting through the metal, but the first way worked a little bit better — probably because my pliers aren’t that great.

2. Apply hot glue — if you have old pins, they are often made of metal. Be careful because the hot glue will quickly heat up the pin.

3. Slap on your magnet and voila!

 

My coworkers loved the magnets — what old pins do you have that you could recycle into something new?